Contact and immersion thermostats
Multiple variants
Stainless steel thermowell
Immediately available
- With side fixing screw
- Internal ø: 6.3 mm
- Connection: DN 15 (1/2")
Multiple variants
thermowell
Immediately available
- Connection thread DN 15 (1/2”)
- For industry and heating systems
Multiple variants
Installation thermostat heatTHERM
Immediately available
- Temperature controller/monitor as built-in thermostat
- Stable switching point position thanks to ambient temperature compensation (as standard)
- Max. switching capacity 16 A, 400 V
Multiple variants
Twist knob for Jumo installation thermostat
Immediately available
- Consisting of:
- Control knob
- Panel
Multiple variants
Installation thermostat heatTHERM
Immediately available
- Safety temperature limiter/safety temperature monitor
- Remains switched off if measurement system destroyed
- Stable switching point position thanks to ambient temperature compensation (as standard)
Multiple variants
Contact thermostat
Immediately available
- Bimetallic thermostat with heatproof plastic housing
Technical data: - Setting range 30-90°C
- Assembly with tightening strap on pipes up to DN 50 (2”)
Multiple variants
Immersion thermostat
Immediately available
- Change-over contact 16A - 250 V
- Thermowell DN 15 (1/2”) nickel-plated 100 mm
- Temperature range 30 - 90°C
Multiple variants
Double boiler thermostat TRB
Immediately available
- Change-over contact 16A - 250 V
- Thermowell DN 15 (1/2”) nickel-plated 100 mm
- Switching differential 6 K
Multiple variants
Thermowells DN 15 (1/2")
Immediately available
- Thread: brass
- Sleeve: copper
Multiple variants
Pressure springs
Immediately available
Multiple variants
Hosing thermostat JET-1
Immediately available
- Technical data:
- Switching capacity: 15 (8) A, 24–250 V~, at 24 V~ min. 150 mA
- Contact: 1 micro-switch used as floating changeover contact (changeover switch)
Multiple variants
Contact thermostats ATR 83
Immediately available
- Capillary system
Technical data: - Switching capacity: 16 (2) A, 24–250 V ~, at 24 V ~ min. 150 mA
- Switching differential: 4 K
Multiple variants
Contact thermostat BRC/A (external scale)
Immediately available
- Application:
- Temperature limit on pipelines
Technical data: - Mounting with fastening strap
Multiple variants
Contact thermostat BRC/I (internal scale)
Immediately available
- Application:
- Temperature limit on pipelines
Technical data: - Mounting with fastening strap
Multiple variants
Boiler double thermostat TRB
Immediately available
- With 1 x temperature controller and 1 x safety temperature monitor
- Thermostat: 0-90°C
- Toggle switch: 10 A, 230V
Multiple variants
Immersion thermostat TC (internal scale)
Immediately available
- Temperature monitor
Application: - Boiler temperature control
Technical data: - Thermostat: 0-90°C
Multiple variants
Accessories for TR 2
Immediately available
- Thermowell 100 mm long, nickel-plated copper
- Control knob
- Ornamental ring
Multiple variants
Construction thermostat JUMO ATHs-1 (TR) External setting
Immediately available
- ATH model range devices are available as temperature controllers TR, temperature limiters TW, safety temperature monitors STW (STB) and safety temperature limiters STB. In the event of any faults, the STB puts the monitored system into a reliable state. Setup thermostats work according to the principle of fluid expansion; a micro switch is used as switching element.
Self-monitoring with the safety temperature limiter STB and the safety temperature monitor STW (STB).
If the measuring systems is destroyed, i.e if the expansion liquid escapes, the pressure in the diaphragm drops with the STB and STW (STB), and the circuit remains open. Unlocking is no longer possible.
When the sensor cools to a temperature under approx. -20°C, the circuit is also opened, when the temperature rises above approx. -20°C, the STB must first be unlocked manually via a re-activation button. STW (STB) reactivation takes place automatically.
Reactivation lock with safety temperature limiter STB.
If the pending temperature exceeds the set limit value on the temperature sensor, the circuit is opened and the micro switch is mechanically locked. Once the critical temperature remains lower that approx. 10% of the scale range (approx. 15% with a limit value setting > +350°C), the micro switch can be unlocked manually. - Protection type IP 54.
- Immersion tube with DN 15 (1/2”) connection
Multiple variants
Construction thermostat JUMO ATHF
Immediately available
- Immersion thermostat model series ATH
Controlling thermostats and monitoring thermal processes. ATH model range devices are available as temperature controllers TR, temperature limiters TW, safety
temperature monitors STW (STB) and safety temperature limiters STB. In the event of any faults, the STB puts the monitored system into a reliable
state. - Setup thermostats work according to the principle of fluid expansion; a micro switch is used as switching element.
Self-monitoring with the safety temperature limiter STB
and the safety temperature monitor STW (STB)
If the measuring systems is destroyed, i.e if the expansion liquid escapes,
the pressure in the diaphragm drops with the STB and STW (STB), and the circuit
remains open. Unlocking is no longer possible. When the sensor
cools to a temperature under approx. -20°C, the circuit is also opened, when
the temperature rises above approx. -20°C, the STB must first be unlocked
manually via a re-activation button. STW (STB) reactivation takes place
automatically.
Reactivation lock with safety temperature limiter STB
If the pending temperature exceeds the set
limit value on the temperature sensor, the circuit is opened and the micro switch is mechanically locked.
Once the critical temperature remains lower that approx. 10% of the scale range
(approx. 15% with a limit value setting > +350°C), the micro switch can be unlocked
manually. - Screw connection with counter nut M 18 x 1 and long-distance cable outlet on housing spigot
Multiple variants
Construction thermostat JUMO ATHs Internal setting
Immediately available
- Setup thermostat model series ATH
- Protection type IP 54
Controlling thermostats and monitoring thermal processes. ATH model range devices are available as temperature controllers TR, temperature limiters TW, safety
temperature monitors STW (STB) and safety temperature limiters STB. In the event of any faults, the STB puts the monitored system into a reliable
state. - Setup thermostats work according to the principle of fluid expansion; a micro switch is used as switching element.
Temperature controller TR und temperature monitor TW
If the pending temperature exceeds the set
target value on the sensor, the micro switch is operated via the gear ration mechanism and the
circuit is opened or closed. In the event of the set
target value remaining low (by the amount of the switching differential), the micro switch is moved back into the output
position.
Self-monitoring with the safety temperature limiter STB
and the safety temperature monitor STW (STB)
If the measuring systems is destroyed, i.e if the expansion liquid escapes,
the pressure in the diaphragm drops with the STB and STW (STB), and the circuit
remains open. Unlocking is no longer possible. When the sensor
cools to a temperature under approx. -20°C, the circuit is also opened, when
the temperature rises above approx. -20°C, the STB must first be unlocked
manually via a re-activation button. STW (STB) reactivation takes place
automatically.
Reactivation lock with safety temperature limiter STB
If the pending temperature exceeds the set
limit value on the temperature sensor, the circuit is opened and the micro switch is mechanically locked.
Once the critical temperature remains lower that approx. 10% of the scale range
(approx. 15% with a limit value setting > +350°C), the micro switch can be unlocked
manually.
Multiple variants
Construction thermostat JUMO ATHs-70 (STB) with external unlocking
Immediately available
- Setup thermostat model series ATH
- Protection type IP 54
Controlling thermostats and monitoring thermal processes. ATH model range devices are available as temperature controllers TR, temperature limiters TW, safety
temperature monitors STW (STB) and safety temperature limiters STB. In the event of any faults, the STB puts the monitored system into a reliable
state. - Setup thermostats work according to the principle of fluid expansion; a micro switch is used as switching element.
Temperature controller TR und temperature monitor TW
If the pending temperature exceeds the set
target value on the sensor, the micro switch is operated via the gear ration mechanism and the
circuit is opened or closed. In the event of the set
target value remaining low (by the amount of the switching differential), the micro switch is moved back into the output
position.
Self-monitoring with the safety temperature limiter STB
and the safety temperature monitor STW (STB)
If the measuring systems is destroyed, i.e if the expansion liquid escapes,
the pressure in the diaphragm drops with the STB and STW (STB), and the circuit
remains open. Unlocking is no longer possible. When the sensor
cools to a temperature under approx. -20°C, the circuit is also opened, when
the temperature rises above approx. -20°C, the STB must first be unlocked
manually via a re-activation button. STW (STB) reactivation takes place
automatically.
Reactivation lock with safety temperature limiter STB
If the pending temperature exceeds the set
limit value on the temperature sensor, the circuit is opened and the micro switch is mechanically locked.
Once the critical temperature remains lower that approx. 10% of the scale range
(approx. 15% with a limit value setting > +350°C), the micro switch can be unlocked
manually.
Multiple variants
Double immersion thermostat JUMO ATHs-120
Currently not in stock
- Devices from the ATH model range consists of two separate measurement and switching systems with the temperature controller TR and safety temperature monitor STW functions
- work according to the principle of fluid expansion; a micro switch is used as a switching element
Self-monitoring with the safety temperature monitor STW
If the measuring systems is destroyed, i.e if the expansion liquid escapes, the pressure in the diaphragm drops with the STW, and the circuit remains open - Unlocking is no longer possible.
Multiple variants
Housing thermostat GT
Immediately available
- With capillary line
- Setting range: 0...90°C
- Sensor element: ø 6.5 x 95 mm
Multiple variants
Construction thermostat JUMO model 603070/0001
Immediately available
- These thermostats work according to the principle of liquid expansion
- When the set temperature is reached, the gear ration mechanism actuates a snap-action switch
- Tested according to DIN 14 597 (replacing DIN 3440)
Multiple variants
Contact / immersion / housing thermostat JUMO heatTHERM AT model 603070/0002
Immediately available
- These thermostats work according to the principle of liquid expansion
- When the set temperature is reached, the gear ration mechanism actuates a snap-action switch
- Tested according to DIN 14 597 (replacing DIN 3440)
Multiple variants
Suitable protective pipes for contact/immersion/housing thermostats
Immediately available
- Screw-in protective pipe with sealing tape for a sensor
- Connection: DN 15 (G 1/2”)
Multiple variants
Suitable protective pipes for construction thermostats
Immediately available
- Screw-in protective pipe with sealing tape for two sensors each with an external diameter of 6 mm (double thermostat)
- Connection: DN 15 (G 1/2”)
Multiple variants
Immersion thermostat TC (external scale)
Immediately available
- Thermostat
Application: - Boiler temperature control
Technical data: - Thermostat: 0-90°C
60 000 54
Contact thermostat IMIT Safety temperature limiter adjustable from 40 to 70°C
Immediately available
- Application:
- Temperature limit on pipelines with manual reset
Technical data: - Setting range: 40 - 70°C
60 028 09
Safety immersion thermostat GST/9SG
Immediately available
- For use in heating
- Incl. thermowell
- Change-over contact load: K1, 16 (4) A, 250 V/AC, K1-2, 6 (1) A, 400 V/AC
Material: Plastic/metal
Protection type: IP 40
Thermowell: DN15 (½“) -14 NPT 100 mm long
60 029 01
Control thermostat TR 2
Immediately available
- As Thermostat
- Setting range: 35 - 90°C
- Toggle switch: 15 (2.5) A 230 V
60 029 02
Immersion sleeve TH/KTC 100
Immediately available
- Thermowell 100 mm long, nickel-plated copper
- Control knob
- Ornamental ring
60 029 03
Twist knob with scale 0-90°C
Immediately available
- Thermowell 100 mm long, nickel-plated copper
- Control knob
- Ornamental ring
60 029 04
Deco-ring with screw for TR 2 *BG*
Immediately available
- Thermowell 100 mm long, nickel-plated copper
- Control knob
- Ornamental ring
60 029 05
Safety temperature limiter STB 400
Currently not in stock - Time of delivery: approx. 4-5 weeks
- Fixed at 100°C as an installation device
- Not suitable for thermal current
- Manual reset
60 055 12
Double heating thermostat JUMO heatTHERM AT model 603070/0170 G 1/2ÆÆ, nickel-plated brass
Immediately available
- Has 2 independent fluid-filled measuring systems and is normally used as a control (TR) and monitoring device (STB or STW), predominantly in heating technology
- The safety temperature limiter (STB) must be manually unlocked after triggering, the safety temperature monitor (STW) switches back automatically
- Push-In® connection technology – installation time reduced by 50%