EBERLE
- Receiver strip for the INSTAT 868r and INSTAT 868r1 transmitters
- For operating actuators in underfloor heating systems
- Fault detection and display
- For 8 zones
- Can switch between heating and cooling
- With real-time clock
Technical data:
Operating voltage: 230 V AC 50/60 Hz
Power consumption: 4 VA
Ambient temperature: 0 to 50°C
Load circuit: 8 closing contacts; 4 A at 230 V (AC)
(Sum of all currents ≤ 2A)
Number of actuators
(3 W electrothermic): max. 16
Transmission frequency: 868 MHz
Antenna: internal
Protection type/protection class: IP 54 / protection insulated
Dimensions (LxWxD): 310 x 90 x 65 mm, incl. top-hat rail
- Switching time setting every 1 h
- Day and night temperature freely selectable
- battery powered for simple assembly
- Wireless radio thermostat, sends to receiver INSTAT 868-a...
- Two selectable control procedures, thus suitable for almost all heater types
- Can be used for heating or cooling (2-pipe systems)
- Freely selectable day and night temperature
- Battery operated
- Hinged cover
- Receiver strip for the INSTAT 868r and INSTAT 868r1 transmitters
- For operating actuators in underfloor heating systems
- Fault detection and display
- Day and night temperature freely selectable
- Hinged lid
- Housing colour pure white similar to RAL 9010
Technical data:
- Wireless radio thermostat, sends to receiver INSTAT 868-a...
- Two selectable control procedures, thus suitable for almost all heater types
- Can be used for heating or cooling (2-pipe systems)
- Receivers for the transmitters INSTAT 868r und INSTAT 868r1
- Fault detection and display
- Emergency operation in the event of faults
Reversal of working direction for cooling instead of heating
- Der INSTAT 868-rep strengths the signals received from the INSTAT 868-r transmitters fully automatically. It is used to increase the range between INSTAT 868-r…wireless thermostats and INSTAT 868-a… wireless receivers. The repeaters integrate themselves into available INSTAT 868 system connections automatically. Only a repeater is required for repeated connections. 2 repeaters can be used in series, i.e. the normal transfer range can be increased up to 90 m.
- Operating voltage: 230 V ~ (195...253 V) 50/60 Hz
- Power loss: < 1.5 W
- Optimum start (the room temperature is reached at the set time)
- 3 pre-set programs
- automatic summer / winter time switchover
- Bimetal technology with thermal feedback
- Surface installation or directly on flush-mounted box with vertical mounting holes or with snap-on mounting on DIN rail
- Can be mounted on adapter frame ARA 1E (not included)
Technical data:
- Bimetal technology with thermal feedback
- Surface installation or directly on flush-mounted box with vertical mounting holes or with snap-on mounting on DIN rail
- Housing colour pure white similar to RAL 9010
- Operating voltage: AC 230 V, 50 Hz
- Temperature range: 0 to 40°C
- Switching current: 16(4) A
- Heating and cooling
- 2 different sensor versions can be used
Technical data:
Temperature range: 0 to 50°C
Adjustable hysteresis: switching temperature differential 0.2 to 5 K (adjustable via cover)
Operating voltage: AC 230 V, 60 Hz
Contact (relay contact): 1 change-over contact
Switching current: 10(4) A
Cable entry: 2 x PG 13, 1 x PG 7
Ambient temperature: -10 to 50°C
Protection type/protection class: IP 54 / protection insulated
- For controlling or monitoring temperatures in living rooms, offices and hotels
- Adjustable range restriction in the setting knob as a heating cost brake
- Suitable for all common Switch lines
- For controlling or monitoring temperatures in living rooms, offices and hotels
- Adjustable range restriction in the setting knob as a heating cost brake
- Fits into all common Switch lines
- Bimetal technology with thermal feedback
- Surface installation or directly on flush-mounted box with vertical mounting holes or with snap-on mounting on DIN rail
- Can be mounted on adapter frame ARA 1E (not included)
Technical data:
- Bimetal technology with thermal feedback
- Surface installation or directly on flush-mounted box with vertical mounting holes or with snap-on mounting on DIN rail
- Can be mounted on adapter frame ARA 1E (not included)
Technical data:
- Bimetal technology with thermal feedback
- Surface installation or directly on flush-mounted box with vertical mounting holes or with snap-on mounting on DIN rail
- Housing colour pure white similar to RAL 9010
- Bimetal technology with thermal feedback
- Surface installation or directly on flush-mounted box with vertical mounting holes or with snap-on mounting on DIN rail
- Housing colour pure white similar to RAL 9010
- For wall mounting
- Heating and cooling
- Ca be used with an exterior or interior setting
- For mounting control units on nearly all international flush-mounted flues
- For covering non-cleanly flush-mounted boxes or for flush-mounted boxes larger than the base plate of the control unit
- Colour pure white
Dimensions (L x W): 168 x 88 mm