EBV

• With pivoting fitting bracket and central PCB, control thermostat, STL, boiler temperature display, operating mode selector switch with integrated TÜV button, inputs and outputs are on terminals at the back of the circuit board, with emergency operating plug and blind cover, installation option for control devices via optional cable set.
  For new installation or replacement of complete control units on boilers as a complete boiler control panel. With swivel fitting bracket, for easy connection a complete PCB is pre-assembled. The outputs and inputs can be created quickly and easily on the back with clamp connections. Boiler operation is also possible without the control system, using an emergency plug (supplied).
  Cable sets (see below) make it suitable for the following controller types:
  
• Delta+ 2 B, Delta+ 23 B
  
• Theta+ 2 B, Theta+ 23 B, Theta+ 233 B, Theta+ 2233 B VV
  Features:
  

• For the control of:
  - 1 x Heat generator, single-stage
  - 1 x direct heating circuit
  - 1 x hot water
  
• Scope of delivery:
  - 1 x Theta + 2B controller
  - 1 x outdoor sensor AF 200
  - 1 x KVT20/2/6 gr boiler immersion sensor, 2 m
  - 1 x cylinder temperature sensor KVT20/5/6 gr, 5 m
  - 1 x BL X1, 16-pin Clamps/terminals
  - 1 x BL X2, 4-pole Clamps/terminals
  - 1 x BL X3, 9-pin Clamps/terminals
  
• Weather-compensated boiler temperature control for variable heating operation
  

• Installation dimensions: 137 x 91 mm
  
• Incl. associated probes and connection terminals
  
• For the control of:
  - 1 x Heat generator, single-stage
  - 1 x direct heating circuit
  - 1 x mixer heating circuit
  - 1 x hot water
  

• Boiler temperature controlled based on outdoor temperature for modulating heating
  
• Simple to operate with rotary potentiometer
  
• Circulation pump logic, automatic summertime/wintertime, frost-protection switch function
  

Cable set for installing Theta+ 2 B to 2233 B VV control units ...

• Not only simple standard systems can be controlled via CETA, more demanding applications can also be achieved by combining several CETA modules. Up to 4 control devices can be combined with one another due to this modular expansion. The individual controller communicate with each other via a databus.
  Every CETA controller can also be operated independently.
  Technical data:
  
• Operating voltage: 230 V / 50 Hz
  
• Max. power consumption: approx. 2.1 VA
  

• With two variable outputs for bivalent applications (solar operation, solid fuel boilers, buffer storage applications, etc.)
  
• For the control of:
  - 1 x Heat generator, 2-stage
  - 1 x direct heating circuit
  - 2 x mixer heating circuit (3-point PI controller)
  - 1 x hot water
  
• Scope of delivery:
  - 1 x Theta + 2233BVV controller
  - 1 x outdoor sensor AF 200
  - 1 x KVT20/2/6 gr boiler immersion sensor, 2 m
  - 1 x cylinder temperature sensor KVT20/5/6 gr, 5 m
  - 2 x flow contact sensor VF202
  - 1 x BL X1, 16-pin Clamps/terminals
  - 1 x BL X2, 4-pole Clamps/terminals
  - 1 x BL X3, 9-pole Clamps/terminals
  - 1 x BL X4, 9-pin Clamps/terminals
  

• Boiler temperature controlled based on outdoor temperature for modulating heating
  
• Simple to operate with rotary potentiometer
  
• Circulation pump logic, automatic summertime/wintertime, frost-protection switch function
  

• For the control of:
  - 1 x Heat generator, single-stage
  - 1 x direct heating circuit
  - 2 x mixer heating circuit (3-point PI controller)
  - 1 x hot water
  
• Scope of delivery:
  - 1 x Theta + 233B controller
  - 1 x outdoor sensor AF 200
  - 1 x KVT20/2/6 gr boiler immersion sensor, 2 m
  - 1 x cylinder temperature sensor KVT20/5/6 gr, 5 m
  - 2 x flow contact sensor VF202
  - 1 x BL X1, 16-pin Clamps/terminals
  - 1 x BL X2, 4-pole Clamps/terminals
  - 1 x BL X3, 9-pole Clamps/terminals
  - 1 x BL X4, 9-pin Clamps/terminals
  
• Weather-dependent boiler temperature control for sliding heating operation
  

• For THETA control systems ?with mains, automatic/manual switch ?and fuse 6.3 A
  
• Fully pre-wired with central terminal strip

• Not only simple standard systems can be controlled via CETA, more demanding applications can also be achieved by combining several CETA modules. Up to 4 control devices can be combined with one another due to this modular expansion. The individual controller communicate with each other via a databus.
  Every CETA controller can also be operated independently.
  Technical data:
  
• Operating voltage: 230 V / 50 Hz
  
• Max. power consumption: approx. 2.1 VA
  

Cable set for installing Delta+ 2 B to 23 B control units ...

• Suitable for Ceta, Theta, Gamma, Delta und Beta device series
  
• 2000 Ω
  
• Cable length: 2 m

• Suitable for Ceta, Theta, Gamma, Delta und Beta device series
  
• ø 6 mm
  
• Cable length: 5 m

• For connecting to heating circuit controllers CETA 104 und 106
  
• Remote control to easily operate all heating circuit parameters from the living room
  
• Room sensor for recording the room temperature
  

• Switching between day-time temperature, night-time temperature or automatic mode
  
• Temperature adjustment
  
• Connection via 2-wire bus
  

• Suitable for ?Ceta, Theta, Gamma, Delta und Beta device series
  
• ø 6 mm
  
• Cable length 2 mm

• For easy rewiring of the sensor terminal strip from GAMMA to THETA

• Remote control with integrated room sensor for recording
  room temperature as a control variable.
  
• A separate room device can be connected to the shared two-care data bus for every heating circuit.
  
• Activates parameters related to the room such as optimising heating and shut-down, adjusting heating characteristics, ambient compensation min. and max. room temperature etc.
  

heatapp! floor is a wireless receiver strip for controlling existing 230V/AC underfloor/wall heating actuators.Heatapp! floor communicates with the heatapp! gateway via wireless, which receives the actual room temperature from heatapp! sense.This set is available from December 2014! ...

• Suitable for boiler control panel KSP A03
  
• With cap and nut
  
• Manual reset
  Technical data:
  

• Weather-dependent boiler temperature control for sliding heating operation
  
• Display of current temperatures
  
• Symbols for heat generators, pumps, mixers and other consumers
  

• Extension to heatcon! EC to add e.g. extra inputs and outputs and a heating circuit
  
• Rail mounting
  
• EM 100 is connected to the EC via the EbV device bus
  

• To remotely control Theta heating control systems from the software version 3.0 via the internet
  
• The heatapp! base t2b can be directly connected to the heating control system THETA+ via the built-in system bus t2b
  
• A heatapp! sense wire can be connected to heatapp! base t2b to use room influence for reference room control