GYS

• DIN 72553
  
• TÜV-tested
  
• Fully insulated pole pliers
  

• The portable power source with a lithium-ion Batteries (LiFePO4) and a sine wave inverter (PSW), supplies electronic devices up to 1500 W with 12 V DC or 230 V AC. With its fast-charging function and high storage capacity, it provides sufficient energy to operate or charge most devices.
  
• Portable Multi-function power source:
  - Suitable for locations without Power supply and devices such as mobile phones, Tools, Machines and electrical appliances
  - Connections Output:
  - 3 x AC socket (230V / 50Hz / 500W)
  - Cigarette lighter 12V
  - 2 x 12V - 10A
  - 3 x USB (5V - 3.1 A (2.4 A max. per output)
  - Quick-charging USB (5 V - 3 A / 9 V - 2 A / 12 V - 1.5 A)
  - 2 x USB-C
  - Protection against short circuit, overcurrent, overvoltage, undervoltage, overcharging and overheating
  
• Charging time at 230V max. (h): 1
  

• Welding process: MIG/MAG/E-Hand
  
• Cuts: No
  
• Amperage (A): 30-220
  

• Voltage: 230 V
  
• For 12 V batteries
  
• Floating function
  

• Welding process: MIG/MAG/E-Hand
  
• Cuts: No
  
• Amperage (A): 30-180
  

• Starts all light vehicles, motorhomes and vans, petrol and diesel, starting current 480A, peak current 1250A
  
• 12 V power source with internal 18 Ah high-performance battery
  
• Can be permanently connected to the mains
  

• Ideal for maintenance and car bodywork operations
  
• No HF-start
  - HF-free ignition extends the life of consumables and eliminates electromagnetic interference that could damage other nearby electronic devices.
  
• Connection to a compressed air system required
  

• MIG/MAG
  - Ideal for smaller assembly, Repair or maintenance work on steel, stainless steel and aluminium sheets
  
• Quick and easy adjustment:
  - Thanks to the SMART Chart, setting the power (4 levels) and wire feed speed is much easier. You can easily find the ideal settings depending on the type and ø of the wire to be welded and the thickness of the sheet to be welded
  
• MIG/MAG burner tube:
  - Burner tube can be dismantled (EURO torch connection)
  - Permanently mounted earth clamp with cable
  - Flux-cored wire welding is also possible
  

• Automatic charger
  
• Voltage: 230 V
  
• Reverse polarity, short circuit and overvoltage protection
  

• For charging motorbikes, cars, classic cars and commercial vehicles with 6, 12 and 24 V Batteries
  
• Seven-stage charging and maintenance phase without monitoring maximises the service life and performance of the Batteries
  
• Protection against short circuit, reverse polarity and overvoltage
  

- Dimensions (mm): ø 6.3 x 13- Length (m): 1.5- (EN ISO 3821) ...

• For metalworking, medium support structures, sheet metal-working, maintenance and repair work
  
• Classification: AWS A 5.1 : E 6013, EN ISO 2560-A - E 42 0 RC 11, DIN 1913 - E 43 21 RC 11

• Charging voltage: 12 V
  
• Booster with lithium Batteries:
  - Starting current (A): 1000
  - Suitable for discharged 12V Batteries: wet, Gel, AGM, Start&Stop
  - Not suitable for LiFePO4 Batteries
  
• Safe starting protects batteries and vehicle electronics:
  - Anti-spark system
  - Schütz against short circuits, reverse polarity and excessive starting currents
  - Thermal protection of the booster
  

• 3 in 1 multi-process: welding machine MIG/Mag, TIG, electrode welding MMA
  
• Welding of sheets 0.6 - 6 mm
  
• 9 synergy lines to facilitate welding in all positions
  

• For welding gases
  
• 2 manometers
  
• 30 L/min
  

• The mains-independent jump starter for 12 V vehicle batteries is equipped with super Capacitors that utilise the residual voltage of the vehicle battery for charging and can start the vehicle engine after a few seconds of charging time. The device is completely independent of the mains supply.
  Technical data
  
• Charging voltage: 12 V
  
• Suitable battery types: 12 V starter battery
  

• For charging 12 V lead-acid batteries 15-160 Ah from cars, commercial vehicles, caravans and lorries
  
• 2 charging options:
  - AGM: Especially for charging at low Temperatures less than 5°C and start-stop batteries
  - Refresh: Revitalisation and recovery of deeply discharged Batteries
  
• Supply mode: Converts the Chargers into a stabilised voltage source, e.g. for demonstration vehicles and the vehicle electrical system when changing batteries
  

• The lithium-based multifunctional device combines a booster for 12V Batteries (cars, SUVs, commercial vehicles, boats), smart jump starter, mobile power source and emergency or signalling light in one.
  
• Charging voltage: 12 V
  
• Booster with lithium Batteries:
  - Starting current (A): 700
  - Suitable for discharged 12V Batteries: wet, gel, AGM, Start&Stop
  - Not suitable for LiFePO4 Batteries
  

• Provides optimum protection for manual electric, MIG/MAG and TIG welding work. The filter darkens fully automatically when the arc is ignited and lightens again when it stops.
  
• Panorama view: 1 x front XXL field of vision + 2x side field of vision
  
• TRUE COLOR technology
  

• TIG-DC welding
  - For welding work on stainless steel, copper and copper alloys
  - 10 pre-sets for storing preferred parameters
  
• TIG DC Pulse
  - Controls the temperature of the weld pool, minimises deformation enabling sheets from 0.3 mm to be joined
  
• 2 ignition options
  - Contact ignition with LIFT ignition
  - Contactless HF ignition
  

• TIG AC/DC
  
• For Repair and maintenance work on aluminium, steel, stainless steel, copper and titanium
  - Aluminium> TIG AC: 10 A - 200 A
  - Steel> TIG DC: 10 A - 160 A
  - Stainless steel> Electrodes: 10 A - 160 A
  
• Storage of up to 50 programmes per process
  

• Single-phase multi-process inverter welder. Its cutting-edge technology ensures excellent arc characteristics in demanding MIG/MAG applications. The built-in synergies greatly facilitate adjustments and reduce spatter during welding. Its illuminated and easily accessible user interface provides precise control of welding parameters to ensure perfect seam quality.
  
• New intuitive and multilingual HMI- 3.5" display
  
• Storage of up to 200 welding programmes for recurring tasks
  

• Solid wire with copper coating for gas shielded arc welding of low or unalloyed carbon steels. Can be used for many metal constructions due to its good mechanical properties.
  
• Applications:
  - Automotive industry
  - Railroad construction
  - Shipbuilding
  - Construction industry in general
  - Vessel, boiler
  
• Classification:
  - AWS 5.18: ER 70S-6 EN ISO 14341-A: G46 4 M21 3Si1
  - DIN 8559: SG2

• Provides optimum protection for manual electric, MIG/MAG and TIG welding work. The filter darkens fully automatically when the arc is ignited and lightens again when it stops.
  
• LCD TRUE COLOR technology
  
• Schütz: DIN 15