Heating and differential pressure controls

• Memory sensor
  
• Suitable for Elster SD1 - SD3, SG2 - SG 3
  
• PVC, 2 m long
  Collector sensor
  

• Suitable for DeltaSol, DeltaTherm
  
• Model: PT1000 sensor
  
• Temperature range: -5...+80°C
  

• Suitable for DeltaSol, DeltaTherm
  
• Model: PT1000 sensor
  
• Dimensions: ø 6 mm, length 1.5 m (silicone line)
  

• To remotely control Theta heating control systems from the software version 3.0 via the internet
  
• The heatapp! base t2b can be directly connected to the heating control system THETA+ via the built-in system bus t2b
  
• A heatapp! sense wire can be connected to heatapp! base t2b to use room influence for reference room control
  

• For the control of:
  - 1 x Heat generator, single-stage
  - 1 x direct heating circuit
  - 1 x hot water
  
• Scope of delivery:
  - 1 x Theta + 2B controller
  - 1 x outdoor sensor AF 200
  - 1 x KVT20/2/6 gr boiler immersion sensor, 2 m
  - 1 x cylinder temperature sensor KVT20/5/6 gr, 5 m
  - 1 x BL X1, 16-pin Clamps/terminals
  - 1 x BL X2, 4-pole Clamps/terminals
  - 1 x BL X3, 9-pin Clamps/terminals
  
• Weather-compensated boiler temperature control for variable heating operation
  

• Installation dimensions: 137 x 91 mm
  
• Incl. associated probes and connection terminals
  
• For the control of:
  - 1 x Heat generator, single-stage
  - 1 x direct heating circuit
  - 1 x mixer heating circuit
  - 1 x hot water
  

• For the control of:
  - 1 x Heat generator, single-stage
  - 1 x direct heating circuit
  - 2 x mixer heating circuit (3-point PI controller)
  - 1 x hot water
  
• Scope of delivery:
  - 1 x Theta + 233B controller
  - 1 x outdoor sensor AF 200
  - 1 x KVT20/2/6 gr boiler immersion sensor, 2 m
  - 1 x cylinder temperature sensor KVT20/5/6 gr, 5 m
  - 2 x flow contact sensor VF202
  - 1 x BL X1, 16-pin Clamps/terminals
  - 1 x BL X2, 4-pole Clamps/terminals
  - 1 x BL X3, 9-pole Clamps/terminals
  - 1 x BL X4, 9-pin Clamps/terminals
  
• Weather-dependent boiler temperature control for sliding heating operation
  

• With two variable outputs for bivalent applications (solar operation, solid fuel boilers, buffer storage applications, etc.)
  
• For the control of:
  - 1 x Heat generator, 2-stage
  - 1 x direct heating circuit
  - 2 x mixer heating circuit (3-point PI controller)
  - 1 x hot water
  
• Scope of delivery:
  - 1 x Theta + 2233BVV controller
  - 1 x outdoor sensor AF 200
  - 1 x KVT20/2/6 gr boiler immersion sensor, 2 m
  - 1 x cylinder temperature sensor KVT20/5/6 gr, 5 m
  - 2 x flow contact sensor VF202
  - 1 x BL X1, 16-pin Clamps/terminals
  - 1 x BL X2, 4-pole Clamps/terminals
  - 1 x BL X3, 9-pole Clamps/terminals
  - 1 x BL X4, 9-pin Clamps/terminals
  

• Remote control with integrated room sensor for recording
  room temperature as a control variable.
  
• A separate room device can be connected to the shared two-care data bus for every heating circuit.
  
• Activates parameters related to the room such as optimising heating and shut-down, adjusting heating characteristics, ambient compensation min. and max. room temperature etc.
  

• For simple solar systems and solid fuel boilers
  
• For standard and high-efficiency recirculation pumps with PWM signal
  
• With 5 inputs and 5 outputs
  Technical data:
  

• For complex solar systems and solid fuel boilers
  
• For standard and high-efficiency recirculation pumps with PWM signal
  
• With 4 inputs and 3 outputs
  Technical data:
  

• For complex solar systems and solid fuel boilers
  
• For standard and high-efficiency recirculation pumps with PWM signal
  
• With 4 inputs and 3 outputs
  Technical data:
  

• For a mixed or unmixed heating circuit
  
• For standard and high-efficiency Circulation pumps with PWM signal
  
• With 5 inputs and 3 outputs
  Technical data:
  

• To remotely control Theta heating control systems from the software version 3.0 via the internet
  
• The heatapp! base t2b can be directly connected to the heating control system THETA+ via the built-in system bus t2b
  
• A heatapp! sense wire can be connected to heatapp! base t2b to use room influence for reference room control
  

• Not only simple standard systems can be controlled via CETA, more demanding applications can also be achieved by combining several CETA modules. Up to 4 control devices can be combined with one another due to this modular expansion. The individual controller communicate with each other via a databus.
  Every CETA controller can also be operated independently.
  Technical data:
  
• Operating voltage: 230 V / 50 Hz
  
• Max. power consumption: approx. 2.1 VA
  

• With capacitive TFT touch panel for remote control and optimization of the heating system
  
• Suitable for: MHCC, LHCC, XHCC
  
• Function: Heating
  

• Boiler temperature controlled based on outdoor temperature for modulating heating
  
• Simple to operate with rotary potentiometer
  
• Circulation pump logic, automatic summertime/wintertime, frost-protection switch function
  

• Boiler temperature controlled based on outdoor temperature for modulating heating
  
• Simple to operate with rotary potentiometer
  
• Circulation pump logic, automatic summertime/wintertime, frost-protection switch function
  

• Boiler temperature controlled based on outdoor temperature for modulating heating
  
• Simple to operate with rotary potentiometer
  
• Circulation pump logic, automatic summertime/wintertime, frost-protection switch function
  

• For simple solar systems or solid fuel boilers.
  
• For standard and high-efficiency recirculation pumps with PWM signal.
  
• With 3 inputs and 1 output.
  Technical data:
  

• For up to 4 mixed and unmixed heating circuits
  
• For standard and high-efficiency Circulation pumps with PWM signal
  
• With 15 inputs and 14 outputs
  Technical data:
  

• For medium-sized solar systems and solid fuel boilers.
  
• For standard and high-efficiency recirculation pumps with PWM signal.
  
• With 3 inputs and 2 outputs.
  Technical data:
  

• Weather-dependent boiler temperature control for sliding heating operation
  
• Display of current temperatures
  
• Symbols for heat generators, pumps, mixers and other consumers
  

• Extension to heatcon! EC to add e.g. extra inputs and outputs and a heating circuit
  
• Rail mounting
  
• EM 100 is connected to the EC via the EbV device bus
  

• Extension to heatcon! EC to add e.g. extra inputs and outputs and a heating circuit
  
• Surface-mounted housing
  
• EM 101 is connected to the EC via the EbV device bus
  

• Living room remote control with room temperature measurement
  
• Connection to EC via a 2-wire bus (h2b-Bus)
  
• Connection of up to five RC 130s to one heatcon! system
  

• Weather-dependent boiler temperature control for sliding heating operation
  
• Display of current temperatures
  
• Symbols for heat generators, pumps, mixers and other consumers
  

• Control unit for connection to the system bus to operate the entire system without browser
  
• Back-lit display
  
• Simple operation via clearly labelled buttons
  

• With pivoting fitting bracket and central PCB, control thermostat, STL, boiler temperature display, operating mode selector switch with integrated TÜV button, inputs and outputs are on terminals at the back of the circuit board, with emergency operating plug and blind cover, installation option for control devices via optional cable set.
  For new installation or replacement of complete control units on boilers as a complete boiler control panel. With swivel fitting bracket, for easy connection a complete PCB is pre-assembled. The outputs and inputs can be created quickly and easily on the back with clamp connections. Boiler operation is also possible without the control system, using an emergency plug (supplied).
  Cable sets (see below) make it suitable for the following controller types:
  
• Delta+ 2 B, Delta+ 23 B
  
• Theta+ 2 B, Theta+ 23 B, Theta+ 233 B, Theta+ 2233 B VV
  Features:
  

Cable set for installing Delta+ 2 B to 23 B control units ...

Cable set for installing Theta+ 2 B to 2233 B VV control units ...

• For heating systems with various heat sources
  For standard and high-efficiency recirculation pumps with PWM signal
  With 6 inputs and 4 outputs + 2 PWM /0-10 V outputs
  Technical data:
  
• Total sensor inputs: 6
  
• Relay connection 230 V: 3
  

• For simple solar systems or solid fuel boilers
  
• For standard and high-efficiency Circulation pumps with PWM signal
  
• With 3 inputs and 1 output
  

• For Delta+ 2B, 23B, 223B
  
• Fully pre-wired with central terminal strip
  
• With mains switch and device fuse 6.3 A

• Suitable for Ceta, Theta, Gamma, Delta und Beta device series

• Suitable for Ceta, Theta, Gamma, Delta und Beta device series
  
• 2000 Ω
  
• Cable length: 2 m