Danfoss

• Seal material: EV220B 6-50 NO, EPDM for water, EV220B 6-50 NO, VITON for oil / air
  
• Testing pressure EV220B 6-10 NO max. 50 bar EVSI 15-50 NO max. 20 bar
  
• Fast-closing
  

• Seal material: EV210B 1.5-3 NO, NBR, EPDM for water,
  
• Testing pressure EV210B 1.5-3 NO max. 50 bar
  
• Fast-closing
  

• With terminal box for EV210B, EV220B, EV250B, IP 67, ED 100%
  
• Power consumption at switch-on AC: 40 VA
  
• Switched-on a.c.: 18 VA,
  

• Without coil, closed and currentless (NC)
  
• For water, oil, compressed air and similar neutral media (max. 50 cSt)
  
• Brass valve housing
  

• Without coil, closed and currentless (NC).
  
• For use in closed circuits with low, undefined pressures e.g. heating systems, for instance, require no differential pressure.
  
• Neutral liquids (max. 50 cSt) and gases
  

• For EV210B, EV220B, EV250B, IP 67, duty cycle 100%
  
• Power consumption at switch-on a.c.: 40 VA, switched-on a.c.: 18 VA
  
• Anchor ø: 13.5 mm

• Without coil, closed and currentless (NC)
  
• For flow rates up to 400 m3 water/h, minimum opening pressure required.
  
• Neutral liquids (max. 50 cSt) and gases
  

• Without coil, closed and currentless (NC). Minimum opening pressure required.
  
• Neutral liquids (max. 50 cSt) and gases
  
• Brass valve housing
  

• For EV210B, EV220B, IP 00 *)
  * Coils 042N with socket 042N0156 = IP 65
  
• Power consumption at switch-on a.c.: 39 VA, switched-on a.c.: 19 VA
  
• Max. ambient temperature: 40 °C
  

These can be used as a replacement for anyother round headed oil nozzle on themarket.Identification/Flow rate SR, HRTo fulfill the requirements of theEN Standards (European Standards)the oil burner nozzles are suppliedwith flow rate specifications as well asspray pattern / angle index'saccording to ...

The be-all and end-all for perfect atomisation: For example, the hole in the nozzle plate is not just a cylindrical hole, but has a special shape. This shape of the hole in the nozzle plate, both on the front and on the back, determines the atomisation pattern and the atomisation angle. A quality th ...

These can be used as a replacement for anyother round headed oil nozzle on themarket.Identification/Flow rate SR, HRTo fulfill the requirements of theEN Standards (European Standards)the oil burner nozzles are suppliedwith flow rate specifications as well asspray pattern / angle index'saccording to ...

The familiar range of Danfoss oil burner nozzles has been extended to include a range of Simplex nozzles in stainless steel.The HFD/HD and SFD/SD type oil nozzles are designed for use in pressure atomising burners for domestic and commercial applications with light and heavy oils.The steel nozzles a ...

The familiar range of Danfoss oil burner nozzles has been extended to include a range of Simplex nozzles in stainless steel.The HFD/HD and SFD/SD type oil nozzles are designed for use in pressure atomising burners for domestic and commercial applications with light and heavy oils.The steel nozzles a ...

• Suitable for Viessmann: Vitoflame 300

The oil nozzle OD LE from Danfoss is used for spraying fuel oil in pressure sprayer burners.The oil nozzle has been improved in essential areas and simultaniously the requirements of the CEN standards were taken into account as far as possible. All oil nozzles now have a nozzle housing which simplif ...

The oil nozzle OD LE from Danfoss is used for spraying fuel oil in pressure sprayer burners.The oil nozzle has been improved in essential areas and simultaniously the requirements of the CEN standards were taken into account as far as possible. All oil nozzles now have a nozzle housing which simplif ...

It is equipped with the Danfoss LE valve. ...

• Suitable for BFP pumps
  
• 220 V 50/60 Hz

• Suitable for:
  - De Dietrich M 100, ref. no.: 97955484
  - OERTLI OES151LE(V), ref. no.: 107112
  
• Single-stage
  
• With side-mounted Solenoid valves
  

• Is used to preheat EL heating oil with viscosities up to 10cSt./20° in small oil burners
  
• The electrical connection on the firing mechanism uses a plug cable; this must be ordered separately where required
  
• FPHE 5: Oil throughput capacity up to 5 kg/h
  

• Shaft: 1-surface
  
• 2-stage
  
• Oil pressure:
  - Stage 1: 7-15 bar
  - Stage 2: 10-25 bar
  

• Nozzle output: DN 6 (1/8")
  
• 1-level
  
• Oil pressure 7-20 bar
  

• Shaft: 1-surface
  
• 2-stage
  
• Oil pressure:
  - Stage 1: 7-15 bar
  - Stage 2: 10-25 bar
  

• Suitable for many conventional small burners

• Suitable for BFP pumps
  
• Ref. no.: 071N0050
  
• Scope of delivery:
  - Spring washer
  - Nut

• Nozzle output: left and right DN 6 (1/8“)
  
• 1-level
  
• Oil pressure 7-20 bar
  

• Shaft: 1-surface
  
• 1-level
  
• Nozzle outlet: DN 6 (1/8")
  

• Shaft: 1-surface
  
• 1-level
  
• Nozzle outlet: DN 6 (1/8”)
  

• Suitable for valve body type RAV and RAVL
  
• Limitable and blockable
  
• Temperature range: 7°C – 26°C
  

• Suitable for all RA 2000 series valve bodies
  
• Temperature range: 8 - 28 °C
  
• Colour: White RAL 9016

• Suitable for valve body type RAV and RAVL
  
• Limitable and blockable
  
• Temperature range: 7°C – 28°C
  

• Lockable and adjustable
  
• With connection options for filling and draining fittings
  Technical data:
  
• Max. operating pressure: 10 bar
  

• For installation in two-pipe heating systems on radiators with lower two-point connection
  
• Can be pre-set and locked
  
• Connection options for filling and draining fittings
  

The be-all and end-all for perfect atomisation: For example, the hole in the nozzle plate is not just a cylindrical hole, but has a special shape. This shape of the hole in the nozzle plate, both on the front and on the back, determines the atomisation pattern and the atomisation angle. A quality th ...