Airfit

• Hose sizes: 8, 10, 13, 19 und 25 mm

• DN 50 coupling side
  
• DN 50 - DN 40 tip
  
• Pressure resistant up to 0.5 bar
  

• For retrofitting on downpipes
  
• Suitable for pip wall thickness to 5.5 mm (the safety set is no longer required)
  
• Approval number: Z-42.1-603
  

• No unpleasant smell, opens at low pressure and closes at overpressure
  
• No need to feed through the roof
  
• Only for vertical mounting
  

• Total height 46 mm

• Very easy installation
  
• Eccentric design
  
• EPDM laminated seal tested according to DIN EN 681
  

• For retrofitting on cast iron cleaners for discharging waste water
  
• Flame retardant according to DIN 4102-B2
  
• Material: PP

• Concentric plug-in fitting
  
• For HT pipes and wastewater pipes
  
• Tested to DIN 4102-B2
  

- For subsequent connection to PVC pipes- Incl. 2 Cable ties- Material: PVC-U- Circle cutter ø 106 mm required (93 910 93) ...

• DIN 4102-B2
  The problem:
  It’s a problem we’ve all come across!
  You’re trying to install standard double sliding sleeves and can’t get a firm hold so you keep on slipping.
  
  The solution:
  The two stop fittings make it possible to apply a crowbar easily and slide the double sliding sleeve plus back onto the pipe end.

• For subsequent connection to PVC pipes
  
• Cut the intake opening using a jigsaw or an angle grinder
  
• Material PVC-U

- Complete incl. holder and drill bit- For plastic and metal pipes- For metal pipes, set a low speed, add cutting oil and switch off the impact mechanism ...

• For plastic cleaning lid
  
• For subsequent connection of HT cleaning pipes, DN 75 and above
  
• For discharging waste water from condensing boilers, sinks, washing machines etc.
  

• Suitable for:
  - Wavin: Si Tech Pipe
  - Dyka: PVC-U-Ultra 3
  - Poloplast: Polo-Kal-NG
  - Piplife: Master 3
  - Valsir®: Tri-Plus
  - Geberit: PE, KG 2000

• Hose size ø: 8, 10, 13 and 19 mm

• Infinitely adjustable from 45-88°
  
• Material: PP

• For retrospective attachment on all drainpipes DN 100/125 as a cleaning opening
  
• To be used inside and outside the building
  
• Seals water and gas-tight permanently
  

• Waterproof min. 5 metres water column
  
• Space-saving
  
• Approval number: Z-42.1-394

• Can be used to seal holes max. ø 25 mm
  
• For DN40 - ø 20 mm
  
• Suitable for permanently sealing bored drain pipes
  

• For plastic pipes DN 50, DN 110, DN 125 and DN 110 spigot
  Advantages:
  
• Fitting in approx. 30 seconds
  
• No drilling, dowels or screws required
  

• For retrofitting to all pipe types
  
• Incl. 2 stainless steel hose clamps

• Infinitely adjustable from 45-88°
  
• Material: PP

- Stainless steel grating 3 mm, 1.4301 V2A K3- 50 mm water trap height in accordance with DIN EN 1253- Pulling out the siphon insert creates a cleaning opening- Impact-resistant PP housing- For pipes DN 100, DN 90 and DN 50 and spigot end DN 110- Grates 120 x 120 mm ...

The problem:It’s a problem we’ve all come across!You’re trying to install standard double sliding sleeves and can’t get a firm hold so you keep on slipping.The solution:The two stop fittings make it possible to apply a crowbar easily and slide the double sliding sleeve plus back onto the pip ...