IMI Heimeier

• Threaded connection: M30 x 1.5
  
• Liquid-filled thermostat
  
• Stable control behaviour even with small differences (<1K)
  

• CEN-certified
  
• Tested according to DIN EN 215
  
• Housing made of corrosion-resistant, dezincification-free gunmetal, nickel-plated
  

• Internal thread on both sides
  
• Max. operating temperature 120 °C
  
• Housing and ball made of corrosion-resistant gunmetal
  

• Shut-off
  
• Adjustable
  
• Operated with a hexagonal wrench SW 5
  

• The required flow rate of the individual heating circuit is set directly on the valve in l/h.
  Integrated flow rate controller in each heating circuit means that the flow rate is never exceeded, even if the neighbouring heating circuits close.
  
• Primary side: 2 freely rotatable nuts with DN 25 (1") IT, flat sealing
  
• Manifold: 2 x manual bleed valve DN 15 (1/2"), 2 x filling and bleeding valve DN 20 (3/4“) hose connection
  

• For radiators with bottom two-point connection e.g. bathroom radiators
  
• Suitable for angular or straight installation
  
• The required flow rate of the individual radiators is set directly on the thermostat valve body, hydraulic balancing is achieved with a single rotation
  

• Housing and ball made of corrosion-resistant gunmetal
  
• Operating pressure: max. 10 bar
  
• Ball valve with T-grip
  

• For installation in Heating and cooling systems. The complete upper part of the Thermostats can be replaced with the Heimeier mounting device without draining the system.
  
• Automatic hydraulic balancing thanks to integrated flow controller, so the flow rate in the Radiators is never exceeded even if the neighbouring valves are closed
  
• The required flow rate of the individual Radiators is set directly on the thermostatic valve body
  

• With shut-off and fine control with
  Double cone
  
• Without stroke limiter
  
• No change in the pre-sets when opening
  or closing
  

HEIMEIER S connection G 3/4 x G 3/4to compensate for different centre distancesHEIMEIER S connection G 3/4 x G 3/4to compensate for different centre distances.Centre distance for each S connection 11.5mmBrand: HeimeierModel: nickel plated brassDN 15 ...

• No check valve
  
• Max. operating temperature: 120°
  
• Internal thread x flange
  

• For radiators with bottom two-point connection e.g. bathroom radiators
  
• Suitable for angular or straight installation
  
• The required flow rate of the individual radiators is set directly on the thermostat valve body, hydraulic balancing is achieved with a single rotation
  

• Concealed upper and lower limits of the temperature range or blocking of a setting with stop clips
  
• Mounting on switch box is possible
  
• With zero position (valve opens at approx. 0 °C)
  

• For mounting all Heimeier thermostat heads on thermostatic valve bodies, see the table
  
• Thread M30 x 1.5 according to factory standard

• Straight shape, IT
  
• Housing made of corrosion-resistant, dezincification-free gunmetal, nickel-plated
  
• With stainless steel spindle and double O-ring seal
  

• For radiators with bottom two-point connection e.g. bathroom radiators
  
• Suitable for angular or straight installation
  
• The required flow rate of the individual radiators is set directly on the thermostat valve body, hydraulic balancing is achieved with a single rotation
  

• Internal thread x flange
  
• With check valve
  
• Max. operating temperature: 90°C
  

• Model DX
  
• Easy to clean
  
• Target value range: 6 °C...28 °C
  

• Threaded connection: M30 x 1.5
  
• Liquid-filled thermostat
  
• Stable control behaviour even with small differences (<1K)
  

• Programming via Bluetooth with the HeimSync app
  
• Auto mode (via home sync app)
  
• Manual mode (temperature setting only)
  

• For Underfloor heating Manifolds
  
• With position indicator at the top
  
• Normally closed (NC)
  

• Suitable for all Heimeier thermostatic valve bodies
  
• Colour: White RAL 9016
  
• with knurled nut
  

• To compensate different connection dimensions when replacing radiators
  
• Connection: DN 15 (R ½”) external thread x union nut (for valve)
  
• Centre distance: 26 mm