MDT
- Each Ducts can be configured independently (input/output)
- Inputs/outputs galvanically isolated from the bus
- Voltage for output operation is generated in the Actuators
- Suitable for 55 mm switch programmes
- Active colour display for function and status display
- Background colour w/b and display brightness adjustable
- For connecting buttons, switches, window contacts
- Any input can be set to an output for 1.5 mA low-current LEDs (not with BE-02230.02)
- New multi-jog function, sends up to 4 values/DPTs to the same or different objects
- 3-gang switching actuator for installation in the switch box, version with monostable Relay
- Current max. 10 A with resistive load, 10 A with 14 µF/2EVG
- Fan coil operating mode:
- Control of 3-speed fans/fan coils
- Outputs interlocked with each other (changeover switching)
- Direct operation via three 1 Bits objects or single 1 Bit object (+/-)
- Automatic operation via 1-byte control value (0-100%)
- Can be used for 2-pipe systems and 4-pipe systems
- Output objects for controlling Heaters/cooling valves
- Day/night function for limiting the ventilation level at night
- Emergency operation in the event of control value failure
- Full version of VisuControl Pro software, for individual programming of VisuControl touch panel
- This software is only available in English
- Version in rail-mounted enclosure, with 4 freely configurable LEDs
- 24 independent function blocks, freely configurable
- Universal logic with up to 5 conditions
- For installation in switch box, max cable length 100 m
- For use within the EU, 868 MHz
- KNX RF+ protocol in system mode
- Size: 7" / 177 mm
- Dimensions (W x H x D): 213 x 171 x 84 mm
- Version with 4 button surfaces and integrated time switch
- Suitable for 55 mm switch programmes
- Active colour display for function and status display
- Expansion of functions
- Lockable manual operation and LED display for each channel
- NC and NO contact operation
- For connecting buttons, switches, window contacts
- New multi-jog function, sends up to 4 values/DPTs to the same or different objects
- Innovative group control with long/extra-long button press
- For connecting buttons, switches, window contacts
- New multi-jog function, sends up to 4 values/DPTs to the same or different objects
- Innovative group control with long/extra-long button press
- Suitable for 55 mm programmes e.g. MDT Button, Button Plus and Button Light
- Dimensions:
- 1-fold: 92 x 92 mm
- 2-gang: 92 x 163 mm
- 3-gang: 92 x 234 mm
- Individual actuation of up to 64 EB/16 DALI groups
- KNX Secure device
- Supports DALI and DALI-2 standard
- The Buttons are freely adjustable as a pair of buttons or individual buttons
- Normally open or normally closed operation, length of button press adjustable
- Transmission of values, forced operation and switching commands can be set
- For 24 V DC motors up to 180 W
- With solar altitude calculation
- Blind motor type: 24 V DC
- Wide range of applications
- New multi-jog function, sends up to 4 values/DPTs to the same or different objects
- Innovative group control with long/extra-long button press
- Suitable for 55 mm switch programmes
- Buttons can be freely configured as button pairs or individual buttons
- One and two-button operation for switch, dimmer, blind, values
- With effective power meter (on RF-AZK1ST)
- In adapter plug, version with monostable relay
- Max. current 16 A into ohmic load, 10 A into 21 µF/3 EB
- VCB-10WS.04:
- Glass frame white
- 318 x 237 mm - VCB-10SW.04:
- Glass frame black
- 318 x 237 mm - VCB-10SI.04:
- Frames brushed stainless steel look
- 314 x 233 mm
- For bidirectional connection between PC and KNX via TCP/IP
- Allows 4 simultaneous connections
- Bus can be programmed via TCP/IP
- Supply voltage: via KNX bus 24V DC
- Max. switching capacity: 10 A with mono-stable relay at ohmic load
- Lockable manual operation and LED display per channel
- Division units: 2
- Line coupling for connecting two KNX bus segments
- Fail safety via galvanic line disconnection