Eltako
- Output: 10 A, 250 V/AC
- Maximum device protection 16 A
- 1 change-over contact, floating
- Division units: 1
- Output: 16 A, 250 V/AC
- 1 NC contact, not floating
- Output: 10 A, 250 V/AC
- 1 NC contact, not floating
- Overrun: 1-12 min
- For R, L and C loads up to 400 W, dimmable energy saving lamps ESL up to 100 W and dimmable 230 V LED lamps up to 100 W
- With nursery and sleep timer
- division unit: 1
- Wireless button F2T55E in pure white gloss
- Individual assembly with retaining plate (screw or glue)
- Suitable for standard 55 switch systems
- MID-calibrated
- Maximum current 3 x 80 A
- Stand-by loss only 0.5 W per path
- Division units: 1
- Output: 10 A, 250 V/AC
- 1 floating change
- Output: 10 A, 250 V/AC
- Control: via wireless button
- Dimensions (W x H x D): 45 x 45 x 33 mm
- Power: 16 A, 250 V/AC
- Overrun 1 to 12 minutes
- Response delay 0 to 12 minutes
- For maintaining the base load (high standby loads may impair/prevent base load detection, e.g. fluorescent lamps, elec. transformers, dimmer switches)
- To be used in a consumer, switch or junction box directly
- Output: 10 A, 250 V/AC
- 1 NC contact, not floating
- Control voltage: 8-230 V/UC
- Division unit: 1
- For R, L and C loads up to 400 W, dimmable energy saving lamps ESL up to 100 W and dimmable 230 V LED lamps up to 100 W
- With nursery and sleep timer
- Division units: 4
- No calibration
- Maximum current: 3 x 80 A
- Ducts: 2
- Output: 16 A, 250 V/AC
- Up to 60 time slots
- Division units: 1
- Output: 16 A, 250 V/AC
- With an internal toroidal current transformer, the AC current flowing through a consumer from 0.1 A to max. 32 A is compared with the set value
- Box-mounted devices
- For R, L and C loads up to 400 W
- Energy saving lamps ESL and 230 V LED lamps can not be switched with dimmers without N connection
- To compensate for inductive interference voltages on control lines
- This can be used to suppress up to three switching devices for the 230 V control inputs via a parallel connection
- Ref. no.: RC12-230 V
- Division units: 1
- 1 NC contact, not floating 600 VA
- 1-10 V control output 40 mA
- Division units: 1
- Output: 16 A, 250 V/AC
- 1 NC contact, not floating
- Output: 16 A, 250 V/AC
- 1 NC contact, floating
- Control voltage: 8-230 V/UC
- Division units: 1
- Output: 10 A, 250 V/AC
- 1 floating change
- Output: 10 A, 250 V/AC
- Control: via wireless button
- Dimensions (W x H x D): 45 x 45 x 33 mm
- Output: 10 A, 250 V
- Incandescent lamps 2000 W
- Glow lamp current to 50 mA
- Wireless button F2T55E in pure white gloss
- Individual assembly with retaining plate (screw or glue)
- Suitable for standard 55 switch systems
- This control can be used to switch the lighting on the extractor bonnet on and off without having to open a window
- Power: 10 A, 250 V/AC
- For recessed mounting
- Without N connection
- 230 V for R and C loads up to 200 W
- Dimensions (W x H x D): 45 x 45 x 18 mm
- Protection type: IP44
- MID conformity
- Voltage: 230/400 V
- Division units: 1
- For capacitive coupling between 2 different external conductors
- Voltage: 400 V/50 Hz
- Output: 10 A, 250 V/AC
- For integrated mounting
- 1 change-over contact, floating
- Box-mounted devices
- For R, L and C loads up to 400 W, dimmable energy saving lamps ESL up to 100 W and dimmable 230 V LED lamps up to 100 W
- Ref. no.: EUD61NPN-UC
- Output: 10A/250 V/AC
- 1 NC contact, not floating
- Disconnects the power supply after switching off
- Division units: 0.5
- For creating and maintaining a venting clearance in very warm series installation devices, e.g. dimmers of 300/400 W and above
- Ref. no.: DS12
- Division units: 1
- Calibration: MID
- Maximum current: 32 A
- Output: 16 A
- Operating voltage: 230 V
- Stand-by loss: 0.8 W
- 1 division unit
- Power: 16 A, 250 V/AC
- 1 NC contacts floating
- Division units: 1
- Calibration: no
- Maximum current: 32 A