Danfoss

100% testedPU = 10 units ...

• Suitable for BFP pumps
  
• 220 V 50/60 Hz

The oil nozzle OD LE from Danfoss is used for spraying fuel oil in pressure sprayer burners.The oil nozzle has been improved in essential areas and simultaniously the requirements of the CEN standards were taken into account as far as possible. All oil nozzles now have a nozzle housing which simplif ...

These can be used as a replacement for anyother round headed oil nozzle on themarket.Identification/Flow rate SR, HRTo fulfill the requirements of theEN Standards (European Standards)the oil burner nozzles are suppliedwith flow rate specifications as well asspray pattern / angle index'saccording to ...

• Shaft: 1-surface
  
• With built-in Solenoid valves
  
• Ref. no.: 071N7170
  

• Suitable for all valve bodies and globe valves type RA
  
• Limitable and blockable
  
• Temperature range: 8°C - 28°C
  

The familiar range of Danfoss oil burner nozzles has been extended to include a range of Simplex nozzles in stainless steel.The HFD/HD and SFD/SD type oil nozzles are designed for use in pressure atomising burners for domestic and commercial applications with light and heavy oils.The steel nozzles a ...

The oil nozzle OD LE from Danfoss is used for spraying fuel oil in pressure sprayer burners.The oil nozzle has been improved in essential areas and simultaniously the requirements of the CEN standards were taken into account as far as possible. All oil nozzles now have a nozzle housing which simplif ...

• Suitable for all valve bodies and globe valves type RA
  
• Limitable and blockable
  
• Temperature range: 7°C – 26°C
  

It is equipped with the Danfoss LE valve. ...

• Shaft: 1-surface
  
• 1-level
  
• Nozzle outlet: on both sides DN 6 (1/8“)
  

• Suitable for valve body type RAV and RAVL
  
• Limitable and blockable
  
• Temperature range: 7°C – 28°C
  

• Without coil, closed and currentless (NC).
  
• For use in closed circuits with low, undefined pressures e.g. heating systems, for instance, require no differential pressure.
  
• Neutral liquids (max. 50 cSt) and gases
  

• Nozzle output: left and right DN 6 (1/8“)
  
• 1-level
  
• Oil pressure 7-20 bar
  

• Without coil, closed and currentless (NC)
  
• For water, oil, compressed air and similar neutral media (max. 50 cSt)
  
• Brass valve housing
  

• Shaft: 1-surface
  
• 1-level
  
• Nozzle outlet: DN 6 (1/8”)
  

The be-all and end-all for perfect atomisation: For example, the hole in the nozzle plate is not just a cylindrical hole, but has a special shape. This shape of the hole in the nozzle plate, both on the front and on the back, determines the atomisation pattern and the atomisation angle. A quality th ...

• For electronic ignition units EBI and Beru except for design Danfoss 052F0036, 052F4031 and Federal Mogul 0096.600.025
  
• Length: 750 mm
  
• Ref. no.: 052F5202

• Can be pre-set
  
• Red protection cap
  
• Thermostatic head connection: Snap fastening
  

The be-all and end-all for perfect atomisation: For example, the hole in the nozzle plate is not just a cylindrical hole, but has a special shape. This shape of the hole in the nozzle plate, both on the front and on the back, determines the atomisation pattern and the atomisation angle. A quality th ...

• For regulating heating and cooling circuits
  
• Shut-off and drained
  
• Adjustment scale with read-out
  

• Shaft: 1-surface
  
• 2-stage
  
• Oil pressure:
  - Stage 1: 7-15 bar
  - Stage 2: 10-25 bar
  

• Can be pre-set
  
• Red protection cap
  
• Thermostatic head connection: Snap fastening