GOK
- High-pressure PS 30, DIN-DVGW-tested
- Hose lines are equipped with a clip (except KLF)
Connections: - On one side, large-bottle (GF), small-bottle (KLF) connection or combi (union nut), on the other large-bottle (GF) external thread or RST
- Suitable for ASF vacuum leak indicator
- For connection to propane and butane gas bottles up to 5 kg
- With safety blow-off valve, response pressure 14 bar
- Connection thread: GAZ (M16x1.5 ET) x ET KLF (small bottle connection)
- Can only be used for exterior mounting downstream of a
pre-stage controller with SAV value = 2.0 bar - Consisting of: Insulating piece, shut-off valve,
gas filter insert, isolating screw connections,
low pressure controller12 kg/h with safety shut-off
valve OPSO (SAV) and safety blow-off valve PRV,
Two junction pieces for soldering connection
and hot-dip galvanised protective box
(H x W x D: 460 x 310 x 155 to 215 mm) - Output: 12 kg/h
- For connection to gas cylinders, for pressure regulation based on nominal pressure
of the gas appliance - KLF x T 1/4 LH-KN
- Outlet pressure: 30 mbar
Consisting of:
- For connecting a pressure compensator with German connection to liquid gas cylinders that are standard on the European market
- Consisting of 4 adapter fittings
- For direct connection to LPG tanks
- Input: POL connection
- Output:
Cutting-ring connection RVS 15 mm, 0.7 bar
with OPSO (SAV) safety shut-off valve and
safety blow-off valve PRV
- Mounted with nut and cutting ring
- DN 8 (1/4”) LH-union nut x RST 8 (union nut)
- For connection to gas cylinders with a filling weight of 33 kg, for pressure regulation to the nominal pressure of the gas appliance
- Also suitable for commercial use
- Cylinders can be changed without interrupting operation
- For connection to liquid gas cylinders up to 14 kg
- KLF x DN 8 (1/4”) LH-KN
- Outlet pressure: 50 mbar
- Backflow preventer for oil suction pipes
to DIN EN 12514-2 - With spacer spring
- Material: hot-dip galvanised sheet steel
- Lockable: square lock including square keys
- Suitable for all 33 kg gas bottles
- Including bracket and connector set for 8/10 mm Cu pipe
- Housing made of die-cast zinc, bichromated
- With Siku insert: 70 µm
- 10 mm x R DN 6 (1/8")
- Cylindrical
- Display device for dry and protected rooms
- 1 relays with NC and NO contact max. 250 V AC, 3.5 A
- Protection type: IP 30
- For Austria
- The test duration according to TRÖI chapter 4.10.4.2. "Tightness test with negative pressure" is:
- 10 minutes for above-ground pipes
- 30 minutes for underground pipes - Consisting of a connection block with integrated shut-off valve, in which a vacuum gauge and a vacuum limiter are mounted
- The suction pressure of the suction pump is limited to the specified test vacuum of -0.3 bar
- Hose breakage protection devices prevent excess gas from escaping in the event of damage or hose loosening and close up the passage of gas as soon as the prescribed operating quantity is exceeded max. 10% above the nominal flow rate.
Fitted between controller and hose. Commercial for hoses >400 mm and private >1500 mm. Exclusively for outdoor use. - For trade and industry
- Input: DN 10 (G 3/8”) LH-union nut
- For direct connection to gas containers
- Input: POL connection
- Output: Cutting-ring connection RVS 15 mm with safety shut-off valve OPSO (SAV) and safety blow-off valve PRV
- For Benelux
- For installation in liquefied petrochemical plants for ground-level house systems
- Incl. ball valve with TAE and wall connection set inside
- RST22: Incl. heat-shrink tubing (length: 500 mm)
- For the stress-free connection of fittings to consumer appliances or pipelines
- Maximum permissible pressure: PS 1 bar
- DN 8 (1/4") LH union nut x IG RP DN 15 (1/2")
- For direct connection to LPG tanks
- Input: POL connection
- Output:
Cutting-ring connection RVS 15 mm, 0.7 bar
with OPSO (SAV) safety shut-off valve
and safety blow-off valve PRV