REMS
- - Inductively brazed and reloadable
- For dry and wet drilling
- For use in concrete, reinforced concrete, masonry, natural stone, asphalt, screed
- ø 32 - 300 mm - Diamond segments with wedge-shaped cut for fast, easy and quiet tapping
- Suitable for all standard pressing machines from REMS and many other manufacturers
Special versions: - 4G: 4-segment pressing jaws (not suitable for steel pipes)
- PR-3 S: Press rings with 3 segments (intermediate pliers Z2 required)
- Cu-INOX for stainless steel, carbon steel and Copper pipe
- V for multi-layer composite and Plastic pipes
- Suitable for
- Nano 230 V
- Battery-powered Nano 10.8 V
- For all common pressfitting systems ø 10-108 mm- 360° rotatable holder for standard crimping pliers- ACC: Automatic return after pressing process (forced return)- Integrated LED work light- 1 x rechargeable battery Li-Ion 14.4 V, 5.0 Ah- Quick charger- Weight with battery: 4.3 kg ...
- With self-priming centrifugal pump
- For filling, rinsing and ventilating closed systems
- Perfect for solar systems, geothermal systems and underfloor/wall heating systems
- Manual mode
- For pipes 10 - 54 mm (1/2” – 2 1/8")
- Ideal for all types of pipes
- - Inductively brazed and reloadable
- For dry and wet drilling
- For use in concrete, reinforced concrete, masonry, natural stone, asphalt, screed
- ø 32 - 300 mm - Diamond segments with wedge-shaped cut for fast, easy and quiet tapping
- Suitable for REMS radial presses 32 kN (except Mini-Press)- In L-Boxx ...
- Cooling unit: 230 V, 50 Hz, 430 W
- For steel, copper, plastic and composite pipes: 1/8"-2", ø 10-60 mm (Accesories required)
- Refrigerant: R-290
- Intermediate clamp Z8 or Mini Z8 required for drive- 180° swivelling- For pressing in hard-to-reach places ...
- For all common pressfitting systems: ø 10 - 40 mm- 360° rotatable holder for Mini crimping pliers- Pressing in less than 4 seconds- ACC: Automatic return after pressing process (forced run)- Integrated LED work light- 1 x rechargeable battery Li-Ion 14.4 V, 2.5 Ah- Quick charger- Weight with bat ...
- Suitable for all standard pressing machines from REMS and many other manufacturers
Special versions: - 4G: 4-segment pressing jaws (not suitable for steel pipes)
- PR-3 S: Press rings with 3 segments (intermediate pliers Z2 required)
- - Inductively brazed and reloadable
- For dry and wet drilling
- For use in concrete, reinforced concrete, masonry, natural stone, asphalt, screed
- ø 32 - 300 mm - Diamond segments with wedge-shaped cut for fast, easy and quiet tapping
- Needle-bearing cutting wheel for simple and low-fatigue work
- For thin-walled stainless steel, steel and copper pipes
- Replacement cutting wheel order no. 80 839 38
- For cutting off pipes at right angles without an outer burr
- For pipes:
- Steel/C-steel ø 12-28 mm
- Copper ø 10-35 mm
- Composite pipes ø 10-40 mm - Maintenance-free gearbox
- For press-fitting system pipes made of rust-proof steel, C-steel, copper ø (8) 22-108 mm, steel pipes DIN EN 10255 (DIN 2440), DN (10) 20-100 ø (1/4) 3/4-4”, cast-iron pipes (SML) DN 50-100, plastic pipes, composite pipes, wall thickness ≤ 7 mm, ø (10) 25-110 mm
- Cutting up to DN 100
- Speed 115 rpm
- For holding standard crimping tongs
- For all common press fitting systems: ø 10-108 mm
- Output: 450 W
- For shafts and pipes
- Power supply: 4 AA batteries (included)
- Display: 2.3 inch TFT-LCD colour display
- - Laser welded and high temperature resistant
- For dry and wet drilling
- For use in concrete, reinforced concrete, masonry, natural stone, asphalt, screed
- ø 32 - 200 mm - Diamond segments with wedge-shaped cut for fast, easy and quiet tapping
- Length: 200 mm
- For all common pressfitting systems ø 10-108 mm- 360° rotatable holder for standard crimping pliers- Acoustic signal after successful pressing process- The pressing tongs remain closed until the manual switchover to retraction- Integrated LED work light- 1 x rechargeable battery Li-Ion 14.4 V, 5 ...
- For all common pressfitting systems: ø 10 - 40 mm- 360° rotatable holder for Mini crimping pliers- Pressing in less than 4 seconds- ACC: Automatic return after pressing process (forced run)- Integrated LED work light- 1 x rechargeable battery Li-Ion 21.6 V, 2.5 Ah- Quick charger- Weight with bat ...
- For all common pressfitting systems ø 10-108 mm- 360° rotatable holder for standard crimping pliers- Acoustic signal after successful pressing process- The pressing tongs remain closed until the manual switchover to retraction- Integrated LED work light- 1 x rechargeable battery Li-Ion 14.4 V, 5 ...
